This particular book was leather bound and missing its back board.
Normally, my first response would be to rebind the book. If the book had any important book plates, I would soak that board in a warm water bath, until the book plates floated off. Then I would reattach them to the new board when dry. However, this book had a nice book plate that was painted with fugitive inks. A water bath would have destroyed it. I had to find another way to replace the board.
Since the front board was not attached, I used it as a guide to cut a new piece of board (make sure to account for the added thickness of materials at the squares). I sanded and back cornered the new board so it would tight against the shoulder. Then I cut new endpapers for the back cover, and attached them to the text block with paste.
I toned a piece of PC4 paper using and acrylics/methyl cellulose mix, to match the original leather. While that dried, I built up the corners on the remaining board.
I took the new board and covered it with the PC4 paper and put it in the press, between blotters, to dry flat. Since this paper is relatively thick, I also infilled the board with a 10 pt card (after pressing).
Because the original spine was a tight back and was still intact, I couldn't bring the new material around the spine. Therefore, I attached the new board as I would the originals, with Japanese tissue at the hinge and joint.
I attached the boards at the inner hinge first, using a strip of Japanese tissue and wheat starch paste. (This has to be done one at a time. Make sure the paste has ample time to dry). I reinforced this by adding additional tissue to the joint with PVA. I also reconstructed the head caps. I glued out a piece of tissue, overlapping on to both boards, and wrapped it around a piece of cord, the width of the spine and the height of the squares.
Finally, I toned all the tissue to match. This is the end result. (Middle: original leather board, Bottom: new PC4 board).
A blog about bookbinding, book conservation, artist's books, printmaking and interning.
Showing posts with label 10 pt board. Show all posts
Showing posts with label 10 pt board. Show all posts
Friday, July 23, 2010
Thursday, June 24, 2010
Spine Repair
This particular book's spine had broken at the joint. The bottom half was also missing. Since the inner hinge and muslin lining were intact, a complete reback would have been overkill.
To infill the missing piece of the spine, I cut a piece of 10 point board the width of the spine and the height needed. I used a Morike similar in color to the cover material to attach the 10 point board and to repair the joints and end caps. This is the completed repair.
To infill the missing piece of the spine, I cut a piece of 10 point board the width of the spine and the height needed. I used a Morike similar in color to the cover material to attach the 10 point board and to repair the joints and end caps. This is the completed repair.
Labels:
10 pt board,
adhesive,
book conservation,
book repair,
japanese tissue,
morike
Thursday, June 10, 2010
Recent Rebacks
These are two cloth rebacks I completed simultaneously. Thankfully for both books the sewing was in tact. This first book's covers were detached, the end papers were delaminating, the spine round was askew, and the first three pages were loose.
I started by tipping in the loose pages with wheat starch paste. Then I pasted out and lined the spine, with Japanese tissue and linen. When both linings were dry, I gently hammered the spine to fix the round. Then I proceeded with a reback repair as usual. This is the end result.
This is the second book.
I started by tipping in the loose pages with wheat starch paste. Then I pasted out and lined the spine, with Japanese tissue and linen. When both linings were dry, I gently hammered the spine to fix the round. Then I proceeded with a reback repair as usual. This is the end result.
This is the second book.
Friday, April 23, 2010
Cook Book
A good friend of mine inherited this cook book from her aunt, in this condition. It is a little dated with some of the recipes, but she claims it also contains priceless ones. Looking for a new project to tackle, I offered to repair it for her. The covers were totally detached, the endpapers were falling off the boards, and the first section and the last two pages were in pieces. (The middle image shows the first section's pages and the bottom is the last page of the index. This is also the page missing the most information).
I began by flattening and repairing the damaged pages. I lined them with heat set tissue, and added additional tissue to the fraying edges. The first pages of the first sections were missing, so when the pages I had were repaired, I guarded them to pages of Dove Grey to complete the section. I also made new endpapers from Dove Grey. Next, I cleaned the spine, repositioned the sections, tipped on the last two pages with paste, and lined the spine with Japanese Tissue. Then I put the first section and end papers in place and put the book in the press. Then I lined the spine again with linen. Once that lining was dry, I sewed on the endpapers, the first section, and repaired the sewing for the sections in the middle which needed it. Then I slightly rounded the spine and lined it with a heavy weight paper to help hold the shape.
Then I made a new spine piece from linen lined Morike, complete with 10 pt board stiffener. I lifted the cloth on the covers, positioned them on the book and carefully moved it to the press. Next I attached the new spine piece to the covers, glued down the turn ins, and then cased in the text block via the linen and new endpapers.
Finally, I did some Japanese tissue repairs on the cover and toned the new spine piece to match with acrylics. (The middle image shows pages from the first section and the bottom is the last page of the index).
I began by flattening and repairing the damaged pages. I lined them with heat set tissue, and added additional tissue to the fraying edges. The first pages of the first sections were missing, so when the pages I had were repaired, I guarded them to pages of Dove Grey to complete the section. I also made new endpapers from Dove Grey. Next, I cleaned the spine, repositioned the sections, tipped on the last two pages with paste, and lined the spine with Japanese Tissue. Then I put the first section and end papers in place and put the book in the press. Then I lined the spine again with linen. Once that lining was dry, I sewed on the endpapers, the first section, and repaired the sewing for the sections in the middle which needed it. Then I slightly rounded the spine and lined it with a heavy weight paper to help hold the shape.
Then I made a new spine piece from linen lined Morike, complete with 10 pt board stiffener. I lifted the cloth on the covers, positioned them on the book and carefully moved it to the press. Next I attached the new spine piece to the covers, glued down the turn ins, and then cased in the text block via the linen and new endpapers.
Finally, I did some Japanese tissue repairs on the cover and toned the new spine piece to match with acrylics. (The middle image shows pages from the first section and the bottom is the last page of the index).
Wednesday, January 13, 2010
Reattaching a Text Block
The following is a simple way to reattach a text block, applicable when the case is in tact. With this particular book the text block was completely detached, but the case was in good shape and I did not want to disturb it.
The first step was to gently lift the old spine lining with a spatula, and attach a new stiffener made of 10 pt board (PVA). Once that dried, I lined the entire spine with Japanese tissue (paste) overlapping slightly on to the boards and leaving some excess at the head and tail.
When the spine lining was dry, I trimmed the excess with a water pen, wrapped it around, and then attached it to the covers (PVA).
While preparing the case, I cleaned and relined the spine of the text block using methyl cellulose and Japanese tissue (paste), leaving a little excess at the shoulders to connect to the case. I also added head and tail bands and a linen spine lining, which was flush with the shoulder. The next step was to tone some Japanese tissue to match the end papers. I did this by mixing acrylics with Klucel G (to stop the Japanese tissue fibers from fraying).
To reattach the text block I needed to simulate opening with the joint intact. I placed the text block in position and raised the cover (with boards) so that the groove aligned with the shoulder of the text block, and applied weights to keep the book in position. Next, I pasted down the excess Japanese tissue from the spine lining. Then I measured out a piece of the toned tissue to be the height and width of the joint, overlapping onto the cover and text block, and attached it using paste. Using a dry brush, I gently tapped the toned tissue against the joint, to ensure it sticks properly. This must dry in position, so it is critical to keep the weights on at all times.
This is the end result:
After repeating on the other side, I repaired the bumped corners and toned the Japanese tissue on the covers.
The first step was to gently lift the old spine lining with a spatula, and attach a new stiffener made of 10 pt board (PVA). Once that dried, I lined the entire spine with Japanese tissue (paste) overlapping slightly on to the boards and leaving some excess at the head and tail.
When the spine lining was dry, I trimmed the excess with a water pen, wrapped it around, and then attached it to the covers (PVA).
While preparing the case, I cleaned and relined the spine of the text block using methyl cellulose and Japanese tissue (paste), leaving a little excess at the shoulders to connect to the case. I also added head and tail bands and a linen spine lining, which was flush with the shoulder. The next step was to tone some Japanese tissue to match the end papers. I did this by mixing acrylics with Klucel G (to stop the Japanese tissue fibers from fraying).
To reattach the text block I needed to simulate opening with the joint intact. I placed the text block in position and raised the cover (with boards) so that the groove aligned with the shoulder of the text block, and applied weights to keep the book in position. Next, I pasted down the excess Japanese tissue from the spine lining. Then I measured out a piece of the toned tissue to be the height and width of the joint, overlapping onto the cover and text block, and attached it using paste. Using a dry brush, I gently tapped the toned tissue against the joint, to ensure it sticks properly. This must dry in position, so it is critical to keep the weights on at all times.
This is the end result:
After repeating on the other side, I repaired the bumped corners and toned the Japanese tissue on the covers.
Labels:
10 pt board,
book repair,
japanese tissue,
klucel g,
methyl cellulose,
spatula
Subscribe to:
Posts (Atom)