Showing posts with label adhesive. Show all posts
Showing posts with label adhesive. Show all posts

Tuesday, August 3, 2010

The Bone Folder

The Bone Folder is a recorded conversation between a bibliophile and master book binder from 1920"s Germany. My book binding instructor translated the text from it's original German, and gave me a copy for binding. I chose to covering it in a paper case because the text block was small, and this binding style is briefly discussed in the text.
The text block was sewn with two pieces of card for end sheets. The paste paper is folded around the card for support. This is an adhesive free binding, so the paper could be easily removed and the text block rebound if desired. If the cover was folded out, this is how the book would look.

Friday, July 23, 2010

Missing Board

This particular book was leather bound and missing its back board.
Normally, my first response would be to rebind the book. If the book had any important book plates, I would soak that board in a warm water bath, until the book plates floated off. Then I would reattach them to the new board when dry. However, this book had a nice book plate that was painted with fugitive inks. A water bath would have destroyed it. I  had to find another way to replace the board.
Since the front board was not attached, I used it as a guide to cut a new piece of board (make sure to account for the added thickness of materials at the squares). I sanded and back cornered the new board so it would tight against the shoulder. Then I cut new endpapers for the back cover, and attached them to the text block with paste.
I toned a piece of PC4 paper using and acrylics/methyl cellulose mix, to match the original leather. While that dried, I built up the corners on the remaining board.
I took the new board and covered it with the PC4 paper and put it in the press, between blotters, to dry flat. Since this paper is relatively thick, I also infilled the board with a 10 pt card (after pressing).
Because the original spine was a tight back and was still intact, I couldn't bring the new material around the spine. Therefore, I attached the new board as I would the originals, with Japanese tissue at the hinge and joint.
I attached the boards at the inner hinge first, using a strip of Japanese tissue and wheat starch paste. (This has to be done one at a time. Make sure the paste has ample time to dry). I reinforced this by adding additional tissue to the joint with PVA. I also reconstructed the head caps. I glued out a piece of tissue, overlapping on to both boards, and wrapped it around a piece of cord, the width of the spine and the height of the squares.
Finally, I toned all the tissue to match. This is the end result. (Middle: original leather board, Bottom: new PC4 board).

Tuesday, July 13, 2010

Corrugated Clamshell Box

A corrugated box is used to rehouse documents or books for additional support and protection. This differs from a phase box, not only in materials used but in design. While a phase box provides support for standing materials, corrugated boxes are meant to lie flat.
This particular box was constructed for a scrapbook of sorts. The object was a series of newspaper and magazine articles, glued to thin board and bound together with a metal ring.
I used a Syracuse University manual to construct the box.
This is an image of the end result, open, with the object.

Monday, July 5, 2010

Building Up Corners

This was a leather bound book that I did Japanese tissue repair for. A couple of the corners were seriously damaged and misshaped.
To infill the corners, I cut small squares of board. These should be small enough to handle, but extend past the book's board edge so they can be trimmed to size later. I parred these squares of board at one corner, until they were thin enough to fit between the existing board. It is important not to par too far out. Remember the thickness of the square should be flush with the book's covers at the board edge. I attached these squares with PVA. Then I covered the new material with Japanese tissue, overlapping on to the original leather.

When all the corners were repaired, I toned them to match, and applied SC 6000 wax. This is the end result.

Thursday, June 24, 2010

Spine Repair

This particular book's spine had broken at the joint. The bottom half was also missing. Since the inner hinge and muslin lining were intact, a complete reback would have been overkill.
 To infill the missing piece of the spine, I cut a piece of 10 point board the width of the spine and the height needed. I used a Morike similar in color to the cover material to attach the 10 point board and to repair the joints and end caps. This is the completed repair.

Wednesday, June 23, 2010

German Springback

I have made one German style Springback before, and decided to make another, smaller one. Following these instructions, I made this.
 Note: Because my Springback was bound in leather, not only did I have to pare the edges, but I also had to pare the joint so the material would fit into the groove. I  was able to do this by first drawing a line where the grooves would be. Then, placing a brush handle under the line and running my paring knife along it. This removed a small amount of the leather, and gave me a guide to work from. I pared the rest thin using a scalpel.

Thursday, June 10, 2010

Recent Rebacks

These are two cloth rebacks I completed simultaneously. Thankfully for both books the sewing was in tact. This first book's covers were detached, the end papers were delaminating, the spine round was askew, and the first three pages were loose.
I started by tipping in the loose pages with wheat starch paste. Then I pasted out and lined the spine, with Japanese tissue and linen. When both linings were dry, I gently hammered the spine to fix the round. Then I proceeded with a reback repair as usual. This is the end result.
This is the second book.

Thursday, June 3, 2010

Leather Reback - Quarter Bound

This is another book from the Syracuse University Ranke Collection that was a good candidate for rebacking. The sewing was completely intact (on raised cords), but the leather at the spine and joint was delaminated.

I was able to remove most the leather from the spine dry, and applied a thin layer of methyl cellulose to remove the rest. Then, I pasted out the spine, and lined it with Japanese tissue. While that dried, I cut strips of linen to be glued down between the cords. Then, I resewed the end bands.
Using a scalpel, I cut along where the leather meets the paper on the boards. I removed the old leather, and lifted the paper slightly. I also lifted the endpapers at the corners and at the spine, for the turn ins. (I also put some brown Morike underneath the lifted paper for support. The paper was brittle and kept breaking. Adding the Morike enabled me to handle it without causing more damage). I measured and cut the new leather and prepared it by paring, dampening with a sponge, pasting it out, and allowing it to sit for the paste to soak in. Then I reattached the boards by gluing out the linen strips and bringing them on to the board. I trimmed the linen so it only overlapped by about half an inch. Then I cut two strips of 10 point board, the exact distance from the spine edge of the board to about 1mm before the paper. This makes the transition between the new and old materials smoother. After gluing down the 10 point strips, I attached the new leather to the corners, and put some silicon release paper between the board and text block. Then I attached the new spine leather, running a bone folder along the cords to accentuate them, and leaving enough material at the turn in to construct the head/tail caps. I wrapped a piece of cord around the joint, and put the book in a press to dry.

Saturday, February 6, 2010

Wallpaper Samples - Part 2 - Wet Board Removal

As previously mentioned, the wallpaper samples I have been working on had two distinct adhesives, spray mount adhesive and gelatin paste. The spray mount could be removed dry by splitting the backing board. I tried to split the board on the samples with gelatin pastes, but the board did not cooperate. I could not get the bone folder between the layers. After struggling with this for a little while, I decided to try wet removal (which is how I identified the gelatin adhesive).
On the first sample, after I had partially removed some board with the bone folder, I dampened the back of the board using a sponge and a spray bottle. When the board was damp, I was able to roll it off in small amount with my thumb. With additional moisture, this proved more successful and I was able to remove board all the way down to the back of the paper. At this point, I decided to try soaking the sample. I spot tested the inks and when they proved water stable, I moved the sample to a warm water bath (supported by Reemay) and soaked the sample for about 10 minutes. Then I removed the sample, flipped the tray and used it to support the sample so that I could work on it over the sink. I was able to sufficiently  remove the board by rolling my thumb over the surface and picking up the final pieces with a spatula. When all the board was removed, I pasted out the sample on a piece of Mylar and lined it with Japanese tissue. Then I dried it between Reemay and blotting paper under weight.
These images show a sample before treatment, after wet removal of the board, and with an untrimmed Japanese tissue lining.
 
This process took longer, but the end result was much cleaner. I was able to remove ALL the board, unlike with the dry removal. And the risk of skinning the paper is greatly reduced as the adhesive gives.