Showing posts with label toning. Show all posts
Showing posts with label toning. Show all posts

Friday, September 17, 2010

Leather Reback - PC4 Paper

This particular book originally had laced on boards. The board were now detached, but were important to keep. Since the original leather was delaminating from the boards, I decided to remove it and attach it to new boards. 
 
The first step was to clean and line the spine. Then I sewed on end bands, constructed end papers, and cut new boards. I attached the boards and put the book in a finishing press, where I molded a damp strip PC4 paper over the spine. This dried over night.
I was able to remove the original leather from the boards gently with a spatula. I also removed and kept the turn-ins. I glued down and turned in the new PC4 spine piece, infilled the boards, and glued down the original leather and turn-ins. Where sections of the turn-ins were missing, I glued down PC4 strips. I lined the board edges and missing areas with Japanese tissue. Then glued down the end papers, and toned the tissue to match. This was then end result.

Saturday, September 11, 2010

Paper Reback

This book was originally bound in marbled paper. The spine had delaminated and pieces were missing. The corners were also badly bumped.
Rather than reconstructing the spine and attempting to tone to match, I decided to attach a new spine piece made from linen lined Morike.  First I removed the remaining spine piece, and cleaned and lined the spine. Then I attempted to re-round it gently with a hammer. I lifted the paper on the boards, and trimmed it back slightly. I also lifted the end papers to make room for the turn ins. I attached the new spine piece, turned it in and pressed the book with jointed boards. This was the end result.

Sunday, September 5, 2010

Leather Reback - Wooden Boards

This was a book from the Ranke collection at Syracuse. The spine was deteriorating and the boards were detached. It was not a good candidate for rebinding because of the level of tooling on the boards. The boards were also wooden, which is not common, and therefore should be preserved. This was the original condition of the book.
I cleaned the spine with methyl cellulose and lined it with Japanese tissue and linen. I made some page repairs with heat set tissue, and resewed the end bands. I lifted the original leather at the spine and corners, attached new, and repaired missing areas or cracks with Japanese tissue. Finally, I toned the tissue to match and applied a coat of SC 6000. This is the end result.
Note: For this particular book, the SC 6000 was a mistake. It caused the tissue areas to shine more than the original leather surface, even after a coating of Klucel G. I would advise against the use of SC 6000 if the original material had lost sheen or if the repaired area is very large.

Friday, July 23, 2010

Missing Board

This particular book was leather bound and missing its back board.
Normally, my first response would be to rebind the book. If the book had any important book plates, I would soak that board in a warm water bath, until the book plates floated off. Then I would reattach them to the new board when dry. However, this book had a nice book plate that was painted with fugitive inks. A water bath would have destroyed it. I  had to find another way to replace the board.
Since the front board was not attached, I used it as a guide to cut a new piece of board (make sure to account for the added thickness of materials at the squares). I sanded and back cornered the new board so it would tight against the shoulder. Then I cut new endpapers for the back cover, and attached them to the text block with paste.
I toned a piece of PC4 paper using and acrylics/methyl cellulose mix, to match the original leather. While that dried, I built up the corners on the remaining board.
I took the new board and covered it with the PC4 paper and put it in the press, between blotters, to dry flat. Since this paper is relatively thick, I also infilled the board with a 10 pt card (after pressing).
Because the original spine was a tight back and was still intact, I couldn't bring the new material around the spine. Therefore, I attached the new board as I would the originals, with Japanese tissue at the hinge and joint.
I attached the boards at the inner hinge first, using a strip of Japanese tissue and wheat starch paste. (This has to be done one at a time. Make sure the paste has ample time to dry). I reinforced this by adding additional tissue to the joint with PVA. I also reconstructed the head caps. I glued out a piece of tissue, overlapping on to both boards, and wrapped it around a piece of cord, the width of the spine and the height of the squares.
Finally, I toned all the tissue to match. This is the end result. (Middle: original leather board, Bottom: new PC4 board).

Wednesday, May 5, 2010

Leather Reback with Previous Repair

I picked this book off the cart because it had a lot of previous repairs. The sewing had broken and the text block was in two pieces. The sections closest to the break were being held in place with pressure sensitive tape. Being a tight backed book, the spine had also broken. The book was being held together by what looked like maroon duct tape. This tape was also on a few pages in the first section. There was also approximately ten pages of images, which had be cut down and taped together, in a random order, with pressure sensitive tape behind the title page.
I began be removing the tape from the spine. The adhesive was delaminating, so it peeled off easily, but did leave some residue on the leather. Next I removed the pressure sensitive tape from the pages of the text block with a tacking iron. I repositioned the now loose folios, cleaned the spine, and lined it with Japanese tissue and linen. Then I repaired the sewing at the break.
I worked on the images while my spine liners were drying. I removed the tape from all the images and lined the sheets with heat set tissue. The images were on single sheets, which I collated and guarded together. Then I tipped them on to the front of the text block with a thin strip of Japanese tissue.
Then I lifted the leather on the cover and attached the text block via the linen. I constructed a new spine piece from linen lined Morike and added a 10 pt board stiffener. I attached this under the leather, the glued the leather back down. Finally, I put some PVA and Japanese tissue on the corners to reshape them, and covered the linen hinge with a strip of Japanese tissue (paste).

This book was an experiment in toning techniques for leather. I toned the new spine piece prior to attaching, and I tried to stipple a variety of hues to better match the leather. My colors were a little light for this book, but overall I was pleased with how it looked. I plan on trying this technique again on other books.

Friday, February 12, 2010

Wallpaper Samples - Part 3- Finishing Touches

Most of the wallpaper samples were intact, but there were a few with large areas missing. I tried two different treatment methods for these large areas. The first, and simplest was to simply replace the missing area with a similarly colored Morike. I would attach the Morike with paste before adding the Japanese tissue lining to the sample. Then I trimmed the Morike with the lining so it was flush. This is an example of this method.
The second method was to apply a thin Japanese tissue to the top of the sample, barely overlapping, with paste. Then tone the tissue with acrylics. (I think watercolor is generally more appropriate for this type of repair, but acrylic is all I had available. Therefore, I ensured this additional Japanese tissue layer could be removed, even after toning, by testing it on a small area. As long as the acrylic is not painted over the tissue edge, there should be no damage to the sample). I used this method sparingly because it was time consuming, difficult to match colors/patterns, and often unnecessary for the size of the missing area. These are two samples for which I did tone. 
After all the samples were treated, I made labels for each and interleaved sheets of Dove Gray, due to the variation in size. Finally, I encapsulated the samples in polyester film (Mylar) and constructed a screw-post binding (2010).